Mid Pin rudder bracket. Sometimes referred to as a Gudgeon, this is best used for replacement of a damaged or bent rudder bracket on a Wilderness Systems kayak made before 2009. It can also be used to install some non-Wilderness Systems rudder kits and...

A Five Pack of round deck fittings common on some Perception kayaks. Fittings hold ¼ inch deck rigging line, or bungee, running through the 3 holes around the perimeter. Mounts onto a flat space on deck. Just over one inch in diameter and no...

Best used as a replacement part for Wilderness Systems sit-on-top kayaks outfitted with Phase3 seating. Two strap assemblies, approximately 7" long. Each assembly has 2 super locks on one inch wide webbing. To entirely replace the seat strap system on a Wilderness Systems sit-on-top...

Five Self Tapping Screws. Useful for a wide range of applications. Bear in mind that these are sharp pointed screws and if used with kayak that have inside access to the hull they could tear a dry bag, or your skin if you reach...

Best used as a replacement blade for touring kayaks. This skeg may utilize a Skeg Spring (not included). Skeg is 15.5 inches long, approximately 5 inches at the widest. Skeg has a flanged pivot hole, spring socket, cable swag-fitting cavity and lift-line hole. While...

The industry standard for kayak assembly. All aluminum, corrosion resistant, strong enough for most, if not all, applications. Most often used to install deck fittings. It is recommend to use silicone sealant between deck and fitting applied to deck. You will need a hand...

This Phase3 seat back part is common on the Wilderness Systems kayaks circa 2002 to 2012. The base of the Phase 3 Spine is 4 and 13/16 inches. The nipple on one side is about ½ inch in diameter, protruding about ½ inch. Phase...

Fits old Perception Tribe series Pre 2019 Fits select older Wilderness Systems models. Fits select older Perception models. Kit includes roto molded seatback with cover, adjustable straps and retainer bungee with hooks.

Hatch Bag (cat bag) for Wilderness Systems, Perception and Dagger kayaks. May fit other makes and models of kayaks as well. For use with the 6" Star Hatch, Wilderness Systems logo hatch and 5" deck plates. Hatch Bag is 5 1/16" outside diameter. -...

In collaboration with Gerber, we present the Dagger River Shorty (a.k.a. the “Dagger Dagger”). If ever a knife was made for a specific purpose, the River Shorty is it. An essential piece of safety gear to always have on-hand in the event that rescue...

Best used as a replacement rudder rest for Wilderness Systems kayaks, and other brands of kayak with a similar rudder rest. The Rudder V-Block is 2 3/4" side to side, ¾" wide, 7/8" high. Screw holes approximately 2 ¼ on center. Mounts onto decks...

Replacement SlideTrax Brass Plates with threaded center for attaching SlideTrax accessories to rails. 1/4-20 thread. 1 inch by 3/4 by 1/8 inch. Pack of 5.

The Leg Lifter is the replacement leg lifter for the Wilderness Systems Phase 3 Seats. Mounting hardware is not included but should be able to be re-used. This is the replacement leg lifter only and not the strap. Replacement leg lifter for Wilderness Systems...

The Perception Conduit 14/Acadia II Replacement Seat Back is a replacement seat back designed to fit the Perception Conduit 14 and Acadia II tandem kayaks. The seat back features two nubs on the bottom corners that insert into holes in the seat bottom of...

Use as a replacement for a damaged Zone seat back pad in Perception branded kayaks as well as select L.L. Bean Manatee kayaks outfitted with Zone seating. Pad is 14.5" wide x 10" tall. Has a drawstring closure with openings on the sides.

Kit contains one flexible wilderness systems hatch cover, (1) 20" tether cord and (1) tether cord washer. Fits - POLARIS, TEMPEST 165/170, TSUNAMI, ZEPHYR

Replacement seat back pad for Perception Conduit 14 and Acadia 2. Seat back pad fits both stern and bow seat back. Hardware not included.

The Koas typically takes one large fin (skeg) in the center and two small fins (skegs) on the sides. Fins can be used in any combination you see fit.Fin depth is 2 9/16 inches. Fits a 9 1/16 inch long skeg box, screw holes...

Sold as a Single Fin. The Koas typically takes two small fins (skegs) on the sides and one large fin (skeg) in the center. Fins can be used in any combination you see fit. Fin depth is 2 1/16 inches. Fits a 9 1/16...

Replacement round Orbix hatch for Wilderness Systems kayaks made before 2015. Can be used for new custom hatch installations on any kayak with the allowable deck space. Outside diameter is 9.75 inches (not including the hinge). The working opening (Iid) is approximately 8 1/4...